Parts & Accessories
- Replacement part for Surly hubs.
Shimano Dura-Ace 9000 Hub Quick Release Skewer. - Axle Type: Standard QR
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum
$50.00 - $91.00
Match your Beyond Black hubs, spokes and decals (each sold separately) with skewers from Zipp. - Sold in pairs - Stainless steel: 85 grams/set - Titanium: 78 grams/set
$70.00 - $90.00
Get rolling again with a replacement freehub body for your Mavic wheels. - For Mavic ID360 hubs
- Supplies full wheel illumination for 700c/29in wheels and smaller - Approximately 40 hrs of battery life - Water resistant design - Includes 3 (AA) batteries - Sold individually (1 wheel) - Easy to install
$57.99 - $69.99
Purchase our Kid Trailer axle for your bike, and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
$1.99 - $6.25
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
Add an Alfine hub, cog, spokes, and a rim to this Shimano Internally Geared Hub Small Parts Kit, and you're ready to rock. - Alfine hubs are packaged without small parts and require this kit plus a cog - Nexus hubs are packaged with small parts and cogs and do not require an additional small parts kit - For 11-Speed Hub - Includes CJ-S700 Cassette Joint for Vertical Dropouts *Cassette joint does not fit Di2 Alfine hubs
Aluminum Tubeless Presta Valve - MTB or Road
$23.40 - $29.99
DT Swiss tubeless-ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type setups. - Durable adhesive tape works as a rim tape and airseal
DT-Swiss Center Lock Adaptor. Allows 6-bolt rotors to be used on Center Lock hubs. - Rotor thickness between 1.8mm and 2.2mm - Easy assembly and only 29g - Made in Switzerland by DT Swiss - 230mm version accepts all rotors up to 203mm diameter - 160mm version accepts all rotors up to 160mm diameter
WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.
WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 46mm
$15.99 - $19.99
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
Thru-Axle hub adapters allow the use of 100 mm front thru-axle hubs in 100 mm QR forks. -Allows the use of modern thru-axle wheels in forks designed for quick-release compatible hubs -100 mm front hub spacing only -CNC-machined AL-6061
$54.00 - $69.99
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Drive Side Axle End Cap
Our thru-axle kit comes with everything you need to mount most 12x142 thru-axle bikes on your KICKR SNAP indoor trainer. This accessory will work with all editions of the Wahoo KICKR SNAP. It includes the following: - Threaded axle spacer M12 x 1.75 Coarse - M12 x 1.5 Medium - M12 x 1.0 Fine - End Cap
$17.99 - $29.99
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
These lightweight valves help prevent clogging from tubeless sealant. - Aluminum - 40mm length
$2.99 - $4.99
The Problem Solvers Axle Nut is perfect for wheels with solid axles (also called bolt-on axles). This quality nut is made of durable chrome-plated steel and features a built-in integrated rotating washer to hold tight.
Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair. Identifying your Hugo rim and selecting the correct valve stem: Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim. Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads: MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.
Protect your tubes without adding bulk with these Rim Strips from FSA. They're lightweight, and come in different lengths according to wheel size. Peace-of-mind comes standard.
The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA - 7075 T6 Aluminum - Similar to Fox Kabolt axle
$9.99 - $153.99
Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable
$39.99 - $49.99
Replacement Cassette body for Origin8 hubs
Zipp’s stainless steel front track skewer replaces your quick release skewer when it’s time to bring your speed weaponry from the road to the track. Tighten it down with a 5 mm Allen key and feel secure on the steepest banking.
- Standard skewers fit either 130 or 135mm spaced hubs, unless listed as another length (i.e. 170mm) - 6061 machined lever with stainless steel pivot and laser-etched logo - All shafts are 5mm in diameter
Stan's All Mountain 29er Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!
Page 1 of 2 Next page